1. Ensure the earphones are in pairing mode (alternating red/blue LED flashes) by holding the MFB for 5 seconds
2. Confirm the device is within 10m range with no obstructions
3. Clear the pairing list by holding the MFB for 10 seconds in power off mode (red & blue LEDs flash 5 times to confirm)
4. If prompted for a passcode, try 0000 or 1234
5. Check for software issues on your phone; try forgetting the device or updating mobile software

1. Pair to the first phone as per usual procedure, then switch off the earphones
2. Switch the earphones back on, enter pairing mode, and pair to the second phone
3. Switch off the earphones once more, then switch on normally (short press until light comes on) so they auto-reconnect to the second phone
4. On the first phone, find “Rockerz 150 Pro” in Bluetooth settings and pair to it as well – both phones should now be connected
5. Try dual pairing with other devices to isolate the issue

1. Restart the device
2. Try a factory reset
3. Check if the same issue happens on different devices and media players
4. Clear any obstructions and move the device closer to the earphones

1. Test the charging cable with another device
2. Use only a 5V/2A wall adapter
3. Check the charging is done until the red LED turns off, indicating a full charge
4. Verify the battery wasn’t tampered with or exposed to electrical damage
5. Check for dirt or debris in the charging port and clean with a cotton swab
6. Confirm the adapter and cable support fast charging

1. Set your phone’s equalizer to normal/default/none/zero (see phone-specific EQ paths below)
2. Try factory resetting the device
3. Move closer to the connected device and remove obstructions
4. Test with different media players and devices to isolate the issue
5. Clean ear wax buildup with a cotton swab and alcohol, then gently blow dry from a distance

1. Check equalizer settings on the connected device
2. Test with a different media player or device to isolate the issue

1. Confirm the device has been fully charged first, until the red LED turns off
2. Use only 5V/2A chargers
3. Check for mishandling, broken wires, or exposure to direct sunlight or fire hazards

1. Unpair/Forget the device and pair again
2. Test controls when connected to a different device
3. Verify the media player supports Bluetooth controls
4. Check for physical damage or hazard exposure

1. Try factory resetting the device
2. Ensure no objects are blocking the microphone
3. Hold the microphone at an adequate distance to pick up your voice
4. Check it wasn’t exposed to hazards like direct sunlight or fire
5. Check it wasn’t exposed to water beyond its resistance rating or dipped in liquid

Rockerz 150 Pro offers up to 150 hours of music playtime and up to 120 hours of talk time per charge. Full charging takes up to 60 minutes.

boAt’s patented fast-charging technology that provides up to 150 minutes of playback from just 10 minutes of charging (may vary by conditions). Use a Type-C 5V/3A adapter for ASAP™ Charge to work effectively.

Rockerz 150 Pro features 65ms low latency via BEAST™ Mode, suitable for entertainment and casual gaming, but it’s not intended for professional gaming equipment needs.

Signature Sound Mode is boAt’s default bass-centric profile, while Balanced Mode is better suited for podcasts, news, and voice-based media. Press the MFB 2 times to switch between the two.

Yes, Rockerz 150 Pro supports dual pairing. Both devices stay connected, but music plays through one at a time, shifting automatically when playback is paused on the first device or the second device receives a call.

No, Rockerz 150 Pro does not support the Qualcomm aptX codec.

No, Rockerz 150 Pro does not support Clear Voice Capture (cVc) technology.

Rockerz 150 Pro earphones are IPX5 certified, meaning they can withstand a low-pressure water jet spray, but cannot withstand submersion in water. It’s recommended not to use them while swimming.